![]() But what if you want a scale jet? Then you still want our J10! When you want the king of 3D jet’s, you want our J10. With UAT, fuel tank, Vector thrust pipe, fuel dot, fuel tank vent, servo extension wire,hardware. LiPo battery charger (required & not included).2S,7.4V,5200mAh×2,LiPo with XT60 type plug (required & not included).9 channel radio system(radio & receiver) (required & not included).SW80B 8KG / SW60B 6KG Turbine engine or similar (required & not included).100mm signal line(JR male+JR male)×8 pcs.Screw (HA3×10mm)×8 pcs (Vertical tail / Tail nozzle).Screw (HM3×10mm)×8 pcs (Horizontal tail).Horizontal Stabilizer carbon tube L=600mm external diameter 6mm×1 pcs.2# Main wing carbon tube L=598mm external diameter 10mm×1 pcs.1# Main wing carbon tube L=598mm external diameter 16mm×1 pcs.LiPo battery charger (required & not included) Metal electric retractable hydraulic landing gear×3 Packing Box + Outer Box(Card mark)/52.87×20.28×17.72(inch)ġ20~125mm from the leading edge of the Main Wing □Zero basis □Beginner □Intermediate ■Advancedħ.4V 25g×2 Metal gear with 80mm lead (left & right ailerons forward)ħ.4V 25g×2 Metal gear with 80mm lead (Flap×2 forward)ħ.4V 25g×3 Metal gear with 80mm lead (Elevator×2 & Rudder×1 forward)ħ.4V 12g×1 Metal gear with 380mm lead with protection function (Nose wheel steering forward)ħ.4V 12g×1 Metal gear with 320mm lead with protection function (Front wheel cover plate forward)ħ.4V 12g×2 Metal gear with 80mm lead with protection function (Rear wheel cover plate forward)ħ.4V 12g×2 Metal gear with 80mm lead with protection function (Retarder plate forward)ĢS,7.4V,5200mAh×2,LiPo with XT60 type plug (required & not included) SW80B 8KG / SW60B 6KG turbine engine (required & not included) Length from Carburetor to Front Bearing: 5" (127mm)ĭistance Between Muffler Mounting Hole Centers: 1.6" (40mm)Ĭrankshaft Thread: 5mm/.8 pitch course threadġ0.5kg (23.1 lb)with 1800cc Aviation kerosene and 750cc smoke Length from Carburetor to Prop Washer: 6.2" (157mm) Height from bottom/Crankcase to top of Cylinder Head: 6.4" (162mm) Recommended Propellers: 22x8, 22x10, 23x8, 23x10ĭistance Between Mounting Hole Centers Same Side: 2.7" (68mm)ĭistance Between Mounting Hole Centers Opposite Side: 3.1" (80mm) Static Thrust: 14.2kg Pulling Force/100 meters altitudeġ2.5kg Pulling Force/1,800 meters altitude (separate receiver style pack can be used) (LiPo & LiFe requiresīest Performance RPM Range: 1,350 - 8,500 ![]() Oil and must be followed exactly for warranty considerationĤ.8 - 6V NiMH/NiCd, or 6.6V LiFe or 7.4V LiPo battery for ignition Two crankshaft bearings-simple design for lighter weightįour petal V-type reed valve bottom induction systemĮngine, spark plug, standoffs, ignition, muffler, instruction manualĢ-cycle oil, mix ratio for this engine is 30 parts gas to one part DLE 55 Gasoline Powered model airplane Engine with Electronic Ignition.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |